Listed below are the parts that make up the plow mounts, frames and blades for Polaris GENERAL vehicles. Included are diagrams and the part numbers for spare part kits. Each diagram and parts listing is specific to that particular mount, frame or blade.
To order a replacement part for any aspect of your plow system, see your authorized Polaris Dealer. To determine if a mount, frame or blade fits your GENERAL, visit the Accessories section of the GENERAL website.
Click on an accessory below to view replacement part numbers and diagrams.
PLOW SYSTEMS
Glacier Pro HD Plow System (part number 3880015)
Includes:
- Glacier Pro Plow Mount (part number 2881763)
- Glacier Pro HD Push Frame (part number 2880260)
- Glacier Pro Plow Blade - 66" Poly (part number 2880269)
Note: Winch required, must be purchased separately.
Glacier HD Plow System (part number 3880016)
Includes:
- Glacier HD Plow Mount (part number 2883256)
- Glacier HD Plow Frame (part number 2882927)
- Glacier Pro Plow Blade - 66" steel (part number 2880268)
Note: Winch required, must be purchased separately.
Glacier Pro HD with Hydraulics (part number 3880014)
Includes:
- Glacier Pro Plow Mount (part number 2881763)
- Glacier Pro HD Push Frame (part number 2880260)
- Glacier HD Plow Blade - 72" Steel (part number 2880270)
- Hydraulic Plow Angle (part number 2889052)
- Plow Control for GENERAL (part number 2883391)
- Glacier Plow Markers - Pair (part number 2872726)
- Replacement HD Rubber Deflector (part number 2858541)
Note: Winch required, must be purchased separately.
MOUNTS
Glacier Pro Plow Mount (Part Number 2881763)
The following table lists the parts included in the Glacier Pro Plow Mount kit, as well as their part numbers and which hardware kits replacements can be found in. Identification numbers correspond to the above diagram. For more information, view the installation instructions. To order a part or a kit, see your Polaris Dealer.
Item | Description | Qty | Hardware Kit/Part Number |
---|---|---|---|
1 | Clevis Pin .016 MM x 40 MM | 1 | kit 2205531 |
2 | Cotter Pin 3x 35 MM Zinc Plated | 1 | kit 2205531 |
3 | Mid Mount | 1 | part number 1022176 |
4 | Flat Washer Zinc Plated M10, 10.5 x O.D. 20 x 2 | 2 | kit 2205531 |
5 | Hex. Bolt 8.8 Zinc Plated M10-1.5 x 30 | 3 | kit 2205531 |
6 | Hex. Flange Bolt Zinc Plated M10-1.5 x 25 MM | 6 | kit 2205531 |
7 | Hex. Flange Bolt Zinc Plated M10-1.5 x 30 MM | 2 | kit 2205531 |
8 | Hex. Flange Nut Zinc Plated M10-1.5 | 6 | kit 2205531 |
9 | Hex. Nylon Nut Zinc Plated M10-1.5 | 2 | kit 2205531 |
10 | Lock Washer Zinc Plated M10 10.2 x O.D. 18.1 x 2.2 | 2 | kit 2205531 |
11 | Pin | 1 | kit 2205531 |
12 | Winch Link Mid-Size | 1 | part number 2205057 |
13 | Spring | 2 | kit 2205531 |
14 | Tension Spring | 1 | kit 2205531 |
15 | Tightening Plate Assembly | 1 | kit 2205531 |
16 | Fairlead Adapter Plate | 1 | kit 2205531 |
17 | Lock | 1 | kit 2205531 |
18 | Kickstand Lever | 1 | kit 2205531 |
19 | Spacer Plate, Upper | 1 | kit 2205531 |
20 | Bumper Bracket Support, Upper | 1 | kit 2205531 |
21 | Mount Plate | 1 | part number 2206310 |
Glacier HD Plow Mount (Part Number 2883256)
The following table lists the parts included in the plow mount kit, as well as their part numbers and which hardware kit that replacements can be found in. Identification numbers correspond to the above diagram. For more information, view the installation instructions. To order a part or kit, see your Polaris Dealer.
Item | Description | Qty | Part Number/ Hardware Kit |
---|---|---|---|
1 | GLACIER Pro Lite Plow Mount Plate | 1 | part number 1023822 |
2 | Tightening Plate | 1 | kit 2207442 |
3 | Winch Link Rod | 1 | kit 2207442 |
4 | Spacer | 1 | kit 2207442 |
5 | Locking Nut | 1 | kit 2207442 |
6 | Hex Bolt, M10-1.5 x 25 | 4 | kit 2207442 |
7 | Lock Washer | 2 | kit 2207442 |
8 | Flat Washer | 2 | kit 2207442 |
9 | Locking Nut, M10-1.5 | 2 | kit 2207442 |
Glacier II Plow Mount (Part Number 2881762)
The following table lists the parts included in the plow mount kit, as well as their part numbers and which hardware kit that replacements can be found in. Identification numbers correspond to the above diagram. For more information, view the installation instructions. To order a part or kit, see your Polaris Dealer.
Item | Description | Quantity | Found In |
---|---|---|---|
1 | Flat Washer, M10, Zinc Plated | 8 | 2206295 |
2 | Hex Bolt, M10 x 1.5 x 25, Zinc Plated | 2 | 2206295 |
3 | Hex Bolt, M10 x 1.5 x 50, Zinc Plated | 2 | 2206295 |
4 | Hex Flange Nut, M8 x 1.25, Zinc Plated | 4 | 2206295 |
5 | Lock Washer, M10, Zinc Plated | 2 | 2206295 |
6 | Tightening Plate Assembly | 1 | — |
7 | Welded Mount Plate | 1 | — |
8 | Winch Link | 1 | — |
9 | Backer Bracket | 1 | — |
10 | Hex Bolt, M8 x 1.25 x 25, Zinc Plated | 4 | 2206295 |
FRAMES
Mid-Size Glacier Pro HD Push Frame (Part Number 2880260)
The following table lists the frame's parts, as well as in which spare kits they can be found. The numbers in the table correspond to the above diagram. For more information, view the installation instructions. To order a kit, see your Polaris Dealer.
Item | Description | Quantity/Found In |
---|---|---|
1 | Rivet 4.8 mm x 19 mm |
4x Plow Kit (2880260) 4x Bumper Kit (2205529) 4x Plow Pivot Kit (2205530) |
2 | Carriage Bolt, M10-1.5 x 30 mm |
2x Plow Kit (2880260) 2x Blade Parts Kit (2205380) |
3 | Clevis Pin, Ø14 mm x 45 mm |
1x Plow Kit (2880260) 1x Angle Selector Kit (2205528) 1x Pins Kit (2205526) 1x Angle Pin Kit (2205068) |
4 | Clevis Pin, Ø14 mm x 60 mm |
1x Plow Kit (2880260) 1x Angle Selector Kit (2205528) 1x Pins Kit (2205526) 1x Angle Pin Kit (2205068) |
5 | Clevis Pin, Ø16 mm x 40 mm |
2x Plow Kit (2880260) 2x Pins Kit (2205526) |
6 | Clevis Pin, Ø20 mm x 115 mm |
1x Plow Kit (2880260) Pins Kit (2205526) |
7 | Cotter Pin, Ø3 x 25 mm |
5x Plow Kit (2880260) 2x Angle Selector Kit (2205528) 5x Pins Kit (2205526) 2x Angle Pin Kit (2205068) |
8 | Fender Washer, M6 |
1x Plow Kit (2880260) 1x Bumper Kit (2205529) |
9 | Flat Washer, M6 |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) |
10 | Hexagonal Bolt, M12 x 1.75 x 40 |
2x Plow Kit (2880260) 2x Blade Parts Kit (2205380) |
11 | Hexagonal Bolt, M6-1.0 x 20 |
2x Plow Kit (2880260) 2x Kickstand Kit (2205534) |
12 | Hexagonal Nut, M12 x 1.75 |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) |
13 | Hexagonal Nylon Nut, M10-1.5 |
2x Plow Kit (2880260) 2x Blade Parts Kit (2205380) |
14 | Hexagonal Nylon Nut, M6-1.0 |
2x Plow Kit (2880260) 2x Kickstand Kit (2205534) |
15 | Hexagonal Nylon Nut, M8-1.25 |
3x Plow Kit (2880260) 1x Bumper Kit (2205529) 2x Blade Parts Kit (2205380) |
16 | Hexagonal Nylon Nut, M12-1.75 |
2x Plow Kit (2880260) 2x Blade Parts Kit (2205380) |
17 | Lock Washer, M6 |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) |
18 | Socket Head Cap Screw, M8-1.25 x 60 mm |
1x Plow Kit (2880260) 1x Bumper Kit (2205529) |
19 | Socket Head Cap Screw, M6-1 x 18 mm |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) |
20 | Pivot Sleeve |
2x Plow Kit (2880260) 2x Blade Parts Kit (2205380) |
21 | Tension Spring |
2x Plow Kit (2880260) 2x Angle Selector Kit (2205528) 2x Pins Kit (2205526) |
22 | Kickstand Spring |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) |
23 | "R" Pin Short |
1x Plow Kit (2880260) 1x Angle Selector Kit (2205528) 1x Pins Kit (2205526) |
24 | Impact Stopper |
1x Plow Kit (2880260) 1x Bumper Kit (2205529) |
25 | 4 Position Bloc |
2x Plow Kit (2880260) 2x Blade Parts Kit (2205380) |
26 | Trip Spring |
2x Plow Kit (2880260) 2x Plow Spring Kit (2205382) |
27 | Trip Stopper |
2x Plow Kit (2880260) 2x Bumper Kit (2205529) 2x Plow Pivot Kit (2205530) |
28 | Clevis Pin, Ø8 mm x 45 mm |
1x Plow Kit (2880260) 1x Angle Selector Kit (2205528) 1x Pins Kit (2205526) |
30 | Angle Lever |
1x Plow Kit (2880260) 1x Angle Selector Kit (2205528) |
31 | Angling Outer Tube |
1x Plow Kit (2880260) 1x Angle Selector Kit (2205528) |
32 | Slide Bar |
1x Plow Kit (2880260) 1x Angle Selector Kit (2205528) |
33 | Shear Pin |
1x Plow Kit (2880260) 1x Shear Pin Kit (2205527) 1x Angle Selector Kit (2205528) 1x Pins Kit (2205526) |
34 | Pin (Mid-Size) |
1x Plow Kit (2880260) 1x Angle Selector Kit (2205528) 1x Pins Kit (2205526) |
35 | Rubber Stopper |
1x Plow Kit (2880260) 1x Bumper Kit (2205529) 1x Angle Selector Kit (2205528) |
36 | Cap |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) 1x Bumper Kit (2205529) |
37 | Pivot |
1x Plow Kit (2880260) 1x Plow Pivot Kit (2205530) |
38 | Kickstand Shoe |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) |
39 | Pedal |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) |
40 | Compression Spring |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) |
41 | Pedal Support |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) |
42 | J Rod |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) |
43 | Handle |
1x Plow Kit (2880260) 1x Angle Selector Kit (2205528) 1x Pins Kit (2205526) |
44 | Eye Bolt, M8-1.25 x 70 |
2x Plow Kit (2880260) 2x Blade Parts Kit (2205380) |
45 | Jam Nut |
1x Plow Kit (2880260) 1x Kickstand Kit (2205534) |
Spare parts can be found in the Kickstand Kit (part number 2205534), Shear Pin Kit (part number 2205527), Bumper Kit (part number 2205529), Plow Pivot Kit (part number 2205530), Angle Selector Kit (part number 2205528), Pins Kit (part number 2205526), Angle Pin Kit (part number 2205068), Plow Spring Kit (part number 2205382), Blade Parts Kit (part number 2205380). To order a spare kit, see your Polaris Dealer.
Kickstand Kit (2205534):
Bumper Kit (2205529):
Plow Pivot Kit (2205530):
Angle Selector Kit (2205528):
Pins Kit (2205526):
Angle Pin Kit (2205068):
Shear Pin Kit (2205527):
In the event of a collision with an obstacle at a speed greater than that recommended for the system, the shear pin (33) of the manual angle mechanism will break to minimize the force of impact in the frame.
If the shear pin is broken, inspect the plow system for damaged parts. If any part is damaged, the impact velocity was greater than what the system is designed to support. you must then buy a replacement part from your Polaris Dealer.
If only the shear pin is broken, the pin can be removed and installed upside down and used again. Follow these steps to change the pin:
1. Using a long nose pliers, remove the two tension springs (21) and then remove the pin (34) retaining the angle lever (30).
2. Remove the half-broken shear pin (33) and reinsert it upside down. You can get a new spare pin (part number 2205527) from your Polaris Dealer.
3. Align the hole in the shear pin (33) with the slot in the angle lever (30) and insert the pin (34), securing the parts in place.
4. Use a long nose pliers to reinstall the two tension springs (21), completing the assembly.
Note that the shear pin is designed only to protect against the impacts affecting right and left ends of the plow. The pin does not protect the system from a central impact.
It's important to always inspect the entire plow system after a shear pin has filed to ensure no other components were damaged by the impact.
Glacier HD Plow Frame (Part Number 2882927)
The following table lists the parts included in the kit, as well as which service kit replacements can be found in. Identification numbers correspond to the above diagram. For more information, view the installation instructions. To order a kit, see your Polaris Dealer.
Item | Description | Quantity | Service Kit |
1 | Weld-Frame | 1 | — |
2 | Weld-Blade Support | 1 | — |
3 | Trip Spring | 2 | 2205382 |
4 | Eyebolt-M8 x 1.25 | 2 | 2207190 |
5 | Nut, Locking-M8 x 1.25 | 2 | 2207190 |
6 | Pivot Sleeve | 2 | 2207190 |
7 | Bolt, Pivot Sleeve-M12 x 1.75 x 40 | 2 | 2207190 |
8 | Nut, Locking-M12 x 1.75 | 2 | 2207190 |
9 | Winch Link | 1 | 2207385 |
10 | Nut, Locking-M10 x 1.5 | 1 | 2207385 |
11 | Clevis Pin, 20 mm DIA. x 115 mm | 1 | 2207190 |
12 | Cotter Pin | 4 | 2207190 2207384 2207385 |
13 | Lock Plate | 2 | 2207385 |
14 | Lock Pin | 2 | 2207385 |
15 | Lanyard | 2 | 2207385 |
16 | Lanyard Choke | 2 | 2207385 |
17 | Shear Pin | 1 | 2205527 |
18 | Handle, Shear Pin | 11 | 2207384 |
19 | Retaining Clip, Clevis Pin | 1 | 2207384 |
20 | Clevis Pin | 1 | 2207384 |
21 | Outer Tube, Angling | 1 | 2207384 |
22 | Slide Bar | 1 | 2207384 |
23 | Clevis Pin, 14 mm DIA. x 45 mm | 1 | 2207384 2207190 |
24 | Clevis Pin, 14 mm DIA. x 60 mm | 1 | 2207384 2207190 |
Lock & Ride Glacier II Pushframe (Part Number 2878822)
The following table lists the frame's parts, as well as in which spare kits they can be found. The numbers in the table correspond to the above diagram. For more information, view the installation instructions. To order a kit, see your Polaris Dealer.
Item | Description | Quantity | Hardware Kit |
1 | M12 Flat Washer | 6 | 2878825 |
2 | M8 Flat Washer | 2 | 2878825 |
3 | M12-1.75 x 90 mm Hex Bolt | 1 | 2878825 |
4 | M10-1.5 x 30 mm Hex Bolt | 2 | 2878825 |
5 | M12-1.75 x 50 mm Hex Bolt | 2 | 2878825 |
6 | M8-1.25 x 25 mm Hex Bolt | 5 | 2204642 |
7 | M8-1.25 x 65 mm Hex Bolt | 2 | 2878825 |
8 | M10-1.5 Nylock Nut | 2 | 2878825 |
9 | M12-1.75 Nylock Nut | 3 | 2878825 |
10 | M8-1.25 Nylock Nut | 9 | 2878825 2204642 |
11 | 13 mm dia x 58 mm x 2.21 N/mm Locking Arm Spring | 1 | 2204642 |
12 | 41 mm dia x 201 mm Tension Spring | 2 | 2877443 |
13 | Adjustable Blade Stop | 2 | 2877504 |
14 | Latch | 2 | 2877450 |
15 | Exhaust Spring | 2 | 7042029 |
16 | 1/16-inch dia x 19.85-inch Cable | 1 | 2877452 |
17 | Pivot Sleeve | 1 | 2878825 |
18 | Pushframe | 1 | 2204640 |
19 | Pivot | 1 | 2204641 |
20 | Locking Arm | 1 | 2204642 |
21 | Locking Arm Bracket | 1 | 2204642 |
22 | Safety Sticker | 1 | — |
23 | M8-1.25 x 60 mm Eyebolt | 2 | 2878825 |
BLADES
Glacier Pro Plow Blade - 72-Inch Steel (Part Number 2880270)
The follow table lists the parts included in the blade kit, as well as which spare kits the parts can be found in. The numbers in the table correspond to the above diagram. For more information, view the installation instructions.
Item | Description | Quantity/Found In |
---|---|---|
1 | Blade | — |
2 | Wear Bar | 1x Wear Bar Kit (2204976) |
3 | Skid Shoe | 2x Skid Shoe Kit (2205071) |
4 | Carriage Bolt - M8 x 1.25 x 25 mm |
8x Wear Bar Kit (2204976) |
5 | Nylon Nut - M8 x 1.25 |
8x Wear Bar Kit (2204976) |
6 | R-Pin |
2x Skid Shoe Kit (2205071) 2x R-Pin Kit (2205070) |
Replacement parts can be found in the Wear Bar Kit (part number 2879875), the Skid Shoe Kit (part number 2205071) and the R-Pin Kit (part number 2205070). To order a replacement kit, see your Polaris Dealer.
Glacier Pro Plow Blade - 66-Inch Poly (Part Number 2880269)
The following table identifies the parts in the blade and which spare kits replacement parts can be found in. The numbers in the table correspond to the above diagram. For more information, view the installation instructions.
Item | Description | Quantity/ Found In |
---|---|---|
1 | R-pin (Hairpin Cotter Pin Zinc Plated 82 mm Long - 4 mm Wire Dia) | 2x Skid Shoe Kit (2205071) |
2 | Rivet (Blind Rivet Round Head Type Steel Black Zinc Plated Ø4.8 mm x 13 mm x 16 mm Head) | 30x 66-Inch Skin Kit (2205069) |
3 | M8 x 1.25 x 25 mm Carriage Bolt | 10x Wear Bar Kit (2879867) |
4 | M8 x 1.25 Self Locking Hexagonal Nut | 10x Wear Bar Kit (2879867) |
6 | Wear Bar | 1x Wear Bar Kit (2879867) |
7 | Blade Framing | — |
8 | Polyethylene Moldboard | 1x 66-Inch Skin Kit (2205069) |
9 | Plow Shoe | 2x Skid Shoe Kit (2205071) |
wear
Replacement parts can be found in the Wear Bar Kit (part number 2879867), the Skid Shoe Kit (part number 2205071), the R-Pin Kit (part number 2205070) and the 66-Inch Skin Kit (part number 2205069). To order a replacement kit, see your Polaris Dealer.
Other accessory kits that are available for purchase are the Plow Marker Kit (part number 2872726), the 66-Inch Hardened Wear Bar Kit (part number 2879868) and the 66-Inch Rubber Deflector Flap Kit (part number 2879866).
Glacier Pro Plow Blade - 66-Inch Steel (Part Number 2880268)
The following table identifies the parts in the blade and which spare kits replacement parts can be found in. The numbers in the table correspond to the above diagram. For more information, view the installation instructions.
Item | Description | Quantity/Found In |
---|---|---|
1 | Blade | — |
2 | Wear Bar | 1x Wear Bar Kit (2879867) |
3 | Skid Shoe | 2x Skid Shoe Kit (2205071) |
4 | M8-1.25 x 25 mm Carriage Bolt | 10x Wear Bar Kit (2879867) |
5 | M8-1.25 Nylon Nut | 10x Wear Bar Kit (2879867) |
6 | R-Pin |
2x Skid Shoe Kit (2205071) 2x R-Pin Kit (2205070) |
Replacement parts can be found in the Wear Bar Kit (part number 2879867), the Skid Shoe Kit (part number 2205071) and the R-Pin Kit (part number 2205070). To order a replacement kit, see your Polaris Dealer.
Other accessory kits that are available for purchase are the Plow Marker Kit (part number 2872726), the 66-Inch Hardened Wear Bar Kit (part number 2879868) and the 66-Inch Rubber Deflector Flap Kit (part number 2879866).
60-Inch Snow Blade (Discontinued - Part Number 2876626)
The 60-inch wear bar is part number 2871806. The heavy duty skid shoes (which come as a pair) are part number 2873423. The standard skid shoes (which come as a pair) are part number 2877245. The deflector for the 60-inch blade is part number 2871808.The deflector for the 72-inch blade is part number 2858541.
ADDITIONAL ACCESSORIES
Glacier Pro HD Plow Extension (Part Number 2880267)
The following table identifies the parts in the blade and which spare kits replacement parts can be found in. The numbers in the table correspond to the above diagram. For more information, view the installation instructions.
Item | Description | Plow Extension Kit (2880267) | Plow Extension Hardware Kit (2205547) | Winch Link Kit (2205542) |
1 | Cotter Pin-Ø3X25mm | 2x | 2x | |
2 | Flat Washer-M6 ID 6.4xOD 12x1.6 | 1x | 1x | |
3 | Hexagonal Bolt-M10-1.5x65 | 2x | 2x | |
4 | Hexagonal Bolt-M6-1.0x20 | 2x | 2x | |
5 | Hexagonal Flange Bolt-M10-1.5x45 | 2x | 2x | |
6 | Hexagonal Flange Nylon Nut-M10-1.5 | 5x | 5x | |
7 | Hexagonal Nut-M12-1.75 | 1x | 1x | |
8 | Hexagonal Nylon Nut-M6-1.0 | 2x | 2x | |
9 | Hexagonal Nylon Nut-M10-1.5 | 1x | 1x | |
10 | Lock Washer-M6 ID 6.1xOD 11.8x1.6 | 1x | 1x | |
11 | Socket Head Cap Screw-M6x1x18mm | 1x | 1x | |
12 | Kickstand Spring | 1x | 1x | |
13 | Extension Clamp | 1x | 1x | |
14 | Cap | 1x | 1x | |
15 | Kickstand Shoe | 1x | 1x | |
16 | Clevis Pin-Ø16mmX40mm | 2x | 2x | |
17 | Compression Spring | 1x | 1x | |
18 | Pedal Support | 1x | 1x | |
19 | Extension Welded Frame | 1x | ||
20 | Extension Sleeve | 2x | 2x | |
21 | Extension Kickstand | 1x | 1x | |
22 | J Rod | 1x | 1x | |
23 | Extension Winch Link, Mid-Size | 1x | 1x | |
Instructions (p/n 9925220) |
1x |
Hydraulic Plow Angle (Part Number 2889052)
Item | Qty. | Part Description | P/N Available Separately | Available Service Kit |
1 | 1 | Cylinder, Plow Angle | 2415814 | n/a |
2 | 2 | Cotter Pin - 3 x 25 | n/a | 2205068 |
3 | 1 | Pin, Clevis - 14 x 45 | n/a | 2205068 |
4 | 1 | Pin, Clevis - 14 x 60 | n/a | 2205068 |
5 | 2 | Cable Tie (not shown) | 7080761 | n/a |
G2 Latch (Part Number 2204642)
For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.