Note: This article applies only to 2021 and older RANGER 570 Mid-Size and CREW 570-4 models. For MY22 RANGER SP 570, Model Year 2022+ RANGER SP 570 Wheel/Brake System Inspection and Tire Rotation.
|Required Tools and Supplies|
|Brake Pad and Rotor Measurement Tools||17mm Socket|
|Tire Depth and Pressure Gauges||Flashlight|
|Torque Wrench||Breaker Bar|
|Shop Rags||Safety Glasses & Nitrile Gloves|
For more information on tools, read Tools and Fasteners Guide.
Always wear safety glasses and nitrile gloves when servicing your Polaris RANGER. To inspect the wheel and brake system and to perform a tire rotation on your RANGER 570 Mid-Size or RANGER CREW 570-4, follow these steps:
1. Take a close look at each tire.
- Verify there is sufficient tread depth. Tires should be replaced once they reach one-eighth inch or 3 millimeters of tread depth.
- Inspect for damage that may compromise the integrity of the tire.
- Next, inspect the tire pressure and verify it is set to specification. The tire pressure for a RANGER 570 Mid-Size should be 10 psi (69 kPa) for all tires. The tire pressure for a RANGER CREW 570-4 should be 10 psi (69 kPa) for the front tires and 14 psi (96 kPa) for the rear tires.
- Lastly, take a close look at how the tires are wearing. If there is irregular wear, it may be time for a rotation.
2. Remove the tires.
- Use a 17mm socket to loosen the lug nuts while the vehicle is on the ground but do not remove.
- Safely elevate the vehicle. Reference your Owner’s Manual for proper lifting techniques.
- Remove the lug nuts and set aside.
- Then remove the wheels and set aside.
3. Now is a great time to look at the brake system.
- Open the hood and inspect the fluid level and condition in the master cylinder. Ensure the level is between the min and max marks. Add fluid as necessary. Caution: After opening a bottle of brake fluid, always discard any unused portion. Brake fluid rapidly absorbs moisture from the air, which causes the boiling temperature to drop. This can lead to early brake fade and the possibility of an accident or serious injury.
- Look at the banjo bolts on the inside of the master cylinder for leaks.
- Follow the lines all the way to both front calipers, looking for any leaks, kinks or damage. Also, ensure the brake line retainers are properly secured.
- Inspect the connections at the front brake calipers for leaks.
- Next, follow the brake lines back to the rear of the vehicle, checking for leaks, kinks and damage.
- Inspect the connections at the junction block in the driver’s side rear wheel well.
- Follow the brake line to the rear brake calipers, looking for leaks, kinks and damage. Also ensure the brake line retainers are properly secured.
- Inspect the rear brake calipers and connections for leaks.
- If inspection reveals any concerns, DO NOT attempt to drive the vehicle. See your authorized Polaris Service Center.
- Once the brake line inspection is completed, close the hood and secure the rubber straps.
4. Next, take a look at the brake pads and rotors. Caution: Brake rotors can become extremely hot after operation. Allow the rotors to cool completely before performing maintenance to prevent the risk of burns.
- Check the brake pad thickness using a suitable tool. Be sure to check the thickness on the inside pads as well. Replace any brake pads that are worn beyond their minimum thickness of 0.030 inches (.762 millimeters).
- Next, use a brake rotor measuring tool to measure the thickness of the brake rotors. Replace the rotors if they are worn below the minimum thickness. Replace front rotors at 0.140 inches (3.56 mm) and rear rotors at 0.170 inches (4.32 mm).
5. Once the brake system inspection has been completed, the tires can be rotated and reinstalled. Rotate the wheels as needed based on wheel configuration. Caution: Due to different configurations, some wheels may not be able to be rotated. Always pay attention to all markings and directional indicators on the tires.
- Install the wheels on the vehicle and hand tighten the lug nuts.
- Safely lower the vehicle until the tires begin to touch the ground. Reference your Owner’s Manual for proper lowering techniques.
- Torque the lug nuts to specification in a crisscross pattern. Steel wheels should be torqued to 36 ft-lbs (49 Nm). Aluminum wheels should be torqued to 30 ft-lbs (41 Nm) plus an additional quarter turn.
- Lower the vehicle completely.
For more information, see your authorized Polaris Dealer. Find a dealer near you with the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.
YouTube® is a registered trademark of Google, Inc.
Unless noted, trademarks are the property of Polaris Industries Inc.
© 2022 Polaris Industries Inc.